Three Details to Resolve Before Your Curtains and Blinds Go In

What experience has taught me to check before plaster, cabinetry and electrical work are finished.

By the time we install curtains and blinds, many of the decisions that determine whether they will look right have already been made.

The recessed pelmet has been built. The cabinetry is in position. Electrical cables have been brought through for the motors. If those details were planned around the finished window furnishings, installation is usually straightforward. If they were not, the available options narrow very quickly.

I have seen expensive new homes with recessed pelmets that cannot accommodate the intended products. I have measured wall-to-wall curtains only to find that new cabinetry now occupies the space where the fabric was supposed to stack. I have also arrived for a final measure and found motor cables positioned in the middle of the blind.

These are not fabric problems. They are planning details that need to be resolved earlier.

There are three areas I now check carefully when working from plans or alongside a designer, builder or electrician.

1. Is the recessed pelmet the right size for what is going into it?

A recessed pelmet is only useful when its dimensions suit the finished window furnishing.

One blind does not need the same space as two blinds. A curtain track has different requirements from a roller blind, while a sheer and blockout combination needs enough room for both products to operate without touching.

I recently saw a new home where the recessed pelmets had been built to exactly the same width as the window openings. On paper, the builder had allowed for window furnishings. In practice, the pelmets were too narrow.

A roller blind needs enough width to cover the window properly. Restricting it to the exact opening leaves light gaps at the sides. Two nearby windows had also been given separate short pelmets, even though one continuous recess could have allowed a single track and sheer curtain to run across both.

The house was already complete. Correcting the pelmets would have meant opening the finished ceiling and rebuilding them, so the homeowner was left working around a decision made much earlier.

Before a pelmet is built, I want to know:

  • Which products are going inside it?

  • Is it holding one blind, two blinds or a curtain track?

  • How much clearance does each product require?

  • Does the furnishing need to extend beyond the window opening?

  • Should adjacent windows be treated separately or as one continuous span?

  • Will there be enough access for installation and future servicing?

Simply writing “recessed pelmet” on a plan is not enough. The internal width and depth need to be based on the products the customer intends to use.

2. Has the cabinetry left enough room for the curtain?

Curtains need somewhere to sit when they are open. The fabric does not disappear at the edge of the glass.

A full-height curtain with generous fullness creates a substantial stack of fabric. If cabinetry extends into that space, the curtain will either cover part of the window when open or finish short of the intended wall.

On one project, the design called for a wall-to-wall curtain. The cabinetry position would have forced the curtain to stop approximately 600 millimetres short of the wall on one side.

It would still have functioned, but it would not have looked intentional. The curtain would have appeared to end wherever the remaining space allowed, rather than completing the room as originally designed.

When we are involved before the cabinetry is manufactured, the solution is often straightforward. The joinery can finish slightly earlier, leaving enough room for the curtain and its stackback. That small adjustment allows the curtain to run across the full wall and creates a much more balanced result.

Once the cabinetry has been manufactured and installed, the conversation becomes more expensive.

I now look beyond the window itself and check the entire elevation. I want to see where wardrobes, shelving, kitchen cabinetry and entertainment units will finish. I also want to understand whether the curtain is intended to cover only the window or continue across the wall.

Before approving cabinetry around a window, discuss:

  • Where the curtain track will begin and end

  • How much room the fabric needs when open

  • Whether the curtain is intended to run wall to wall

  • Whether doors, drawers or cupboards will open into the curtain

  • Whether the cabinetry layout has changed since the window furnishings were quoted

Changes made after the final measure also need to be communicated. If cabinetry is extended or flooring levels change after we have measured, the finished curtain will still be made to the dimensions we recorded.

3. Are the motor cables positioned where the products actually need them?

Motorised curtains and blinds require more than power somewhere near the window. The cable must emerge in a position that works with the product, brackets and surrounding structure.

We recently measured an L-shaped arrangement of motorised Roman blinds fitted almost wall to wall within a recessed area. When we checked the final positions, the electrical cables came through exactly where the blinds needed to sit.

The electrician had brought the cables down where access was available during construction, but there was very little spare room within the recess.

The builder suggested adding another piece of timber above the blinds. This made for a secure fixing point and created a small cavity to feed through the cable. It was a simple solution that allowed the installation to proceed neatly.

The builder saw the answer because he understood the structure. We understood where the Roman blinds and brackets needed to sit. Both pieces of information were required to resolve the problem.

The experience also reinforced something I have learnt about communicating cable positions. Pointing to a general area during a site walk is not precise enough.

If an electrician encounters timber, a beam or another service in the nominated position, the cable will need to move. They need to know which alternative positions will still work rather than making that decision without information about the blind or track.

For motorised products, I now want to establish:

  • Which end of the product contains the motor

  • The preferred cable position

  • The acceptable alternative area if the first position is obstructed

  • Where brackets and tracks will be fixed

  • Whether additional timber is required behind the plaster

  • Whether the system is hardwired or wire-free

  • Who the electrician should contact if the agreed position cannot be used

Additional timber noggins are especially important for long tracks, tall curtains and heavy products. It is much easier for the builder to install secure fixing support before the plaster goes on than for us to search for suitable fixing points afterwards.

What I check at each stage

The customer does not need to select every fabric at the beginning of a renovation or new build. The structural decisions still need to reflect the likely products.

During the planning stage

I review the plans, elevations and window schedule to understand:

  • The intended treatment for each window

  • Whether products will be layered

  • Where curtains will stack

  • Which products are likely to be motorised

  • Where cabinetry meets the windows

This is also the right time to establish a realistic budget.

Before plaster and electrical work are completed

We confirm:

  • Recessed pelmet dimensions

  • Track and blind positions

  • Additional timber required for fixing

  • Power and cable locations for motorised products

  • Any spaces that cabinetry needs to preserve

These details become difficult to change once the walls and ceilings are finished.

Before the final measure

The relevant surfaces need to be complete, including cabinetry and finished flooring levels.

After we complete the final measure, changes to the room must be communicated before manufacturing begins. A new cabinet, altered ceiling detail or different floor finish will affect the dimensions and installation.

Specific information leads to a better finish

Experience has taught me that vague provisions create avoidable problems.

“Allow for curtains” does not tell the cabinetmaker how much stackback to leave. “Provide a recessed pelmet” does not tell the builder how large it needs to be. “Bring power to the window” does not tell the electrician where the motor and brackets will sit.

The useful questions are specific:

What product is being installed? How much space does it need? Where will it sit when it is open? What needs to be hidden behind the finished surface?

When those questions are answered early, the curtains and blinds look like part of the original design. When they are left until installation, we are choosing from whatever options remain.

Planning a renovation or new build?

If your plans are still flexible, we can review the window details and identify what needs to be resolved before construction progresses.

Talk to us at Evans Curtains and Blinds about your project.

Next
Next

Thinking About New Curtains or Blinds? Start With These Questions